Innotech Genesis V4 System Manual de usuario Pagina 7
- Pagina / 115
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation Instructions for Innotech Genesis Systems
Edition: 011100
iii
TABLE OF CONTENTS – (Continued)
SECTION/PARAGRAPH PAGE
4-1.2.4.1. Voltage Checks. .........................................................................4-14
4-1.2.4.2. Current Checks. .........................................................................4-15
4-1.2.4.3. Resistance Checks. .....................................................................4-17
4-1.2.5. Checking Analogue Output Wiring. .............................................4-17
4-1.3. INSTALL AISCs. ..........................................................................................4-18
4-1.4. SET JUMPER PLUGS. ................................................................................4-18
4-1.4.1. Address Jumpers. ............................................................................4-19
4-1.4.2. End-of-Cable Jumpers. ...................................................................4-19
4-1.4.3. Analogue Output Jumpers. ............................................................4-20
4-1.5. APPLY PARTIAL POWER. .......................................................................4-21
4-1.6. LOAD SOFTWARE AND CONFIGURE THE CONTROLLER(S). .....4-22
4-1.6.1. Loading Gen2Works. ......................................................................4-22
4-1.6.2. Configuring a Controller. ...............................................................4-22
4-1.7. INITIAL TESTS. ..........................................................................................4-23
4-1.7.1. Gen2Mon Software. ........................................................................4-23
4-1.7.2. Performing Initial Tests. .................................................................4-24
4-1.7.2.1. First Phase Testing. ...................................................................4-24
4-1.7.2.2. Second Phase Testing. ...............................................................4-25
4-1.7.2.3. Third Phase Testing. .................................................................4-25
4-1.8. FINAL SYSTEM CHECKOUT. ..................................................................4-26
APPENDIX A-NETWORK INSTALLATION. ................................................................A-1
A-1. OVERVIEW. ............................................................................................................A-1
A-2. GENESIS I AND GENESIS II PRODUCTS. .......................................................A-1
A-2.1. NET COMMS. ...............................................................................................A-1
A-2.2. GLOBAL POINTS. .......................................................................................A-1
A-2.3. GENII RS485I ISOLATED RS485 COMMS. ............................................A-2
A-3. GENESIS I AND GENESIS II CABLE SPECIFICATIONS. .............................A-2
A-4. INSTALLATIONS. .................................................................................................A-2
A-4.1. GENESIS II COMMS WIRING TOPOLOGY. ........................................A-3
A-4.1.1. Adding Modules to the Comms Link. ...........................................A-3
A-4.1.2. Linking Networks in Different Locations. ....................................A-4
A-4.1.3. Multi-Network Arrangement. ........................................................A-4
A-4.2. GENESIS COMMS WIRING CONSIDERATIONS. ...............................A-5
A-4.2.1. Genesis Comms Wiring Connections. ...........................................A-5
A-4.2.2. Genesis I Connections. ....................................................................A-7
A-4.2.3. Genesis II Connections. ..................................................................A-8
A-4.2.4. GENII POLY SWITCH Board. .....................................................A-9
A-4.2.5. GENII 485I Isolated RS485 Comms Card. ...................................A-10
A-4.2.6. GENII RPTR Repeater Module. ...................................................A-11
A-4.2.7. GENII MPI Modem and Printer Interface. ..................................A-12
A-4.2.8. Genesis I Non-Isolated Comms. .....................................................A-13
- Innotech 1
- PROPRIETARY 3
- TRADEMARK 3
- TABLE OF CONTENTS 5
- LIST OF ILLUSTRATIONS 8
- LIST OF TABLES 10
- GENESIS II 18
- DIGITAL INPUT MODULE 18
- GEN II AI REM 19
- REMOTE MODULE INTERFACE 20
- D.I.M. D.I.M. D.O.M. D.O.M 22
- SIDE VIEW TOP VIEW 23
- 90 DEGREES 23
- GENESIS II DDCINNOTECH 29
- GEN II MPC 36
- ANALOGUE INPUT MODULE 41
- 3233 343536 42
- DIGITAL OUTPUT MODULE 44
- ++ = Positive Comms Line 46
- −− = Negative Comms Line 46
- A1 A2 A3 A4 A5 A6 48
- ABCDEFGH I J 50
- DI 1 DI 2 DI 3 DI 4 DI 5 53
- • C+ = RS 485 (+) Signal 54
- • C- = RS 485 (-) Signal 54
- • SHLD = Comms cable shield 54
- COMMS DIGITAL INPUTS SENSOR 55
- COMMISSIONING 56
- 4-1.2.2 60
- 4-1.2.2.1 60
- JUMPER WIRE 61
- 4-1.2.2.2 62
- SWITCH CLOSED 63
- SWITCH OPEN 63
- GENII DI REM 63
- 4-1.2.3 64
- EXTERNAL 65
- 4-1.2.4 67
- ANALOGUE 69
- CONDITIONERS 69
- 4-1.2.4.2 70
- 4-1.2.4.3 72
- 4-1.2.5 72
- 4-1.4.1 74
- 4-1.4.2 74
- 4-1.4.3 75
- INNOTECH 76
- 4-1.7.1 78
- 4-1.7.2 79
- 4-1.7.2.1 79
- Example A 84
- Example B 84
- Zone A Zone B 85
- Zone BZone A 85
- 1234- - - 29 30 31 32 86
- 1 234- - - 29 30 31 32 86
- 1 234- - - -29 30 31 32 86
- Pin Strip 90
- BOTTOM EDGE OF BOTTOM BOARD 90
- Screen1 2 100
- Isolated 101
- 89 90 91 92 93 107
- MPI With Isolated RS485 108
- Comms Cables for Port 2 108
- Comms Cables for Port 1 108
- Edition 011100 109
- APPENDIX B- DATA SHEETS 110
Relacionado con productos y manuales para Software Innotech Genesis V4 System
Software Innotech iSEA Manual de usuario
(44 paginas)
(44 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales