search

Innotech Device Communications Manual de usuario Pagina 15

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 42
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 14
Page 7
Chapter 2 – Preliminary Information
DS 99.05 – Ethernet Setup Manual for Device Communications
2
Factory default settings of Innotech devices
All Innotech controllers and devices are congured at the factory with default Ethernet
settings that can be modied based on your network requirements. These settings
are required in order to correctly congure these devices so that correct functionality is
achieved within your network conguration. The following sections provide the default
Ethernet settings for devices equipped with an Ethernet port, and the default Innotech
network settings for devices that are covered in this document.
Device Address IP address Subnet mask
Default
Gateway
Net comms
port
Genesis II
DHCP
AutoIP
DHCP
AutoIP – 169.168.x.x
DHCP or
255.255.255.0
DHCP or
0.0.0.0
20,000
MAXIM III
DHCP
AutoIP
DHCP
AutoIP – 169.168.x.x
DHCP
255.255.255.0
DHCP or
0.0.0.0
20,000
MAXIM 1010
DHCP
AutoIP
DHCP
AutoIP – 169.168.x.x
DHCP
255.255.255.0
DHCP or
0.0.0.0
20,000
IG01 Static 192.168. 2.10 0 255.255.255.0 0.0.0.0 20,000
IG03 Static 192.168. 2.10 0 255.255.255.0 0.0.0.0 20,000
IG04 Static 192.168. 2.10 0 255.255.255.0 0.0.0.0 20,000
CONV-E
DHCP
AutoIP
DHCP
AutoIP – 169.168.x.x
DHCP
255.255.255.0
DHCP or
0.0.0.0
20,000
IWS01 Static 192.168. 2.10 0 255.255.255.0 0.0.0.0 20,000
Default Ethernet settings
It is important to know the default Ethernet settings of your Innotech device(s) in order
to prepare the device(s) for deployment on your particular LAN. The table below shows
each applicable controller or device, and the associated factory default Ethernet settings.
Default Ethernet settingsTable 2-2:
Default device address and baud rate
The Innotech network device settings allow your device to communicate with iComm,
the Innotech communication software hub. Each device must have a unique device
address, and must be congured at the same baud rate as iComm software in order
to communicate on an Innotech network. The table below shows the default network
settings of each applicable controller or device as they are shipped from the factory.
Device Innotech device address Baud rate
Genesis II 1 57, 6 0 0
MAXIM III 1 57, 6 0 0
MAXIM 1010 1 57, 6 0 0
IG01 2 57, 6 0 0
IG03 2 57, 6 0 0
IG04 2 57, 6 0 0
CONV-E N/A 9,600
Default Innotech network settingsTable 2-3:
**The IWS01 does not have a physical Innotech device address.
Vista de pagina 14
1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 41 42

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Sensores Innotech Device Communications
Sensores Innotech Maxim Manual de usuario   (60 paginas)
Sensores Innotech Genesis II Digital Controller (v5) Manual de usuario   (124 paginas)
  • E-Tech AV-GAD Moeller Marine V.I.O. Warwick
  • Audiovox Dvd Portátil / Reproductor De Blu-Ray Life is good Los teléfonos inteligentes Alesis Ecualizadores de audio BOXLIGHT Proyectores ADIC No
  • Wells HDG-4830G Scarlett SC-213 LG LGW150 Lenovo G710 Notebook Vidyo HD-220
  • Digi-Frame DF-560 Manual de usuario Bbk DV113SI Manual de usuario Samson Expedition XP308i Especificaciones Indesit UFAN 400 Manual de usuario Samsung HW-J6001 Manual de usuario